Autor Tópico: [Samba] Compartilhando dois hds. [RESOLVIDO]  (Lida 13383 vezes)

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
[Samba] Compartilhando dois hds. [RESOLVIDO]
« Online: 08 de Agosto de 2010, 16:19 »
boa tarde.
Instalei um servidor samba em um computador de um cliente. Neste servidor, tem dois hds. Um hd onde esta instalado o Sistema Operacional tem duas pasta compartilhadas em rede. Essas pastas estão acessiveis para todos os usuarios. Todos conseguem criar, editar e excluir documentos.
Nele tem outro hd, formatado como ext3. Neste outro hd, eu consigo criar, editar e excluir pasta, ate compartilha-las. Mas os outros computadores nao conseguem acessa-las. Enxergam na rede mas nao conseguem entrar nas pastas. Quem esta no servidor, consegue fazer qualquer coisa nestas pastas, mas na rede nao esta sendo possivel.
Uso o Ubuntu 10.04.
O que posso fazer para compartilhar esta pasta?
Lembrando que no outro hd tem duas pastas compartilhadas e estão sendo acessiveis.
« Última modificação: 10 de Agosto de 2010, 15:02 por marcionugas »

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #1 Online: 08 de Agosto de 2010, 16:48 »
Pode mostrar seu smb.conf? Em especial, a parte dos compartilhamentos.
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #2 Online: 08 de Agosto de 2010, 16:57 »
meu smb.conf eu somente alterei o workgroup = META, o compartilhamento foi feito desta maneira em nos hds.
no primeiro que tem o Ubuntu instalado, na pasta pessoal, criei duas pastas, formularios e documentos. Cliquei com o botão direito em cima das pastas e foi em propriedades, alterei as permissões para criar e excluir, foi na aba compartilhar e compartilhei, marcando as tres opções que aparece. Assim esta funcionando perfeitamente em um hd, mas nao no outro. Fiz o mesmo processo no outro hd mas  nao vingo. Mesmo quando vou acessar esta pasta no ubuntu mesmo, da pau, as pastar sitadas acima eu acesso, mas a outra no outro hd me da um erro de localização de rede, fala que nao pode montar uma rede windows.

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #3 Online: 08 de Agosto de 2010, 17:07 »
Não acho que seja algo nas configurações (seção [global]) mas sim nos próprios compartilhamentos. Por isso pedi pra vê-los.
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #4 Online: 08 de Agosto de 2010, 17:40 »
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not made any basic syntactic errors.
#
#======================= Global Settings =====================================
[global]

# workgroup = NT-Domain-Name or Workgroup-Name
   workgroup = META

# server string is the equivalent of the NT Description field
   server string = REDHAT PDC SERVER

# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
   hosts allow = 172.17.,127.

# if you want to automatically load your printer list rather
# than setting them up individually then you'll need this
   printcap name = /etc/printcap
   load printers = yes

# It should not be necessary to spell out the print system type unless
# yours is non-standard. Currently supported print systems include:
# bsd, sysv, plp, lprng, aix, hpux, qnx
   printing = cups

# This option tells cups that the data has already been rasterized
cups options = raw

# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
;  guest account = pcguest

# this tells Samba to use a separate log file for each machine
# that connects
 log file = /var/log/samba/%m.log
# all log information in one file
#   log file = /var/log/samba/smbd.log

# Put a capping on the size of the log files (in Kb).
   max log size = 0

# Security mode. Most people will want user level security. See
# security_level.txt for details.
#   security = user
# Use password server option only with security = server
;   password server = <NT-Server-Name>

# Password Level allows matching of _n_ characters of the password for
# all combinations of upper and lower case.
;  password level = 8
;  username level = 8

# You may wish to use password encryption. Please read
# ENCRYPTION.txt, Win95.txt and WinNT.txt in the Samba documentation.
# Do not enable this option unless you have read those documents
  encrypt passwords = yes
  smb passwd file = /etc/samba/smbpasswd
  time server = yes
  log level = 1

# The following are needed to allow password changing from Windows to
# update the Linux system password also.
# NOTE: Use these with 'encrypt passwords' and 'smb passwd file' above.
# NOTE2: You do NOT need these to allow workstations to change only
#        the encrypted SMB passwords. They allow the Unix password
#        to be kept in sync with the SMB password.
  unix password sync = Yes
  passwd program = /usr/bin/passwd %u
  passwd chat = *New*UNIX*password* %n\n *ReType*new*UNIX*password* %n\n *passwd:*all*authentication*tokens*updated*successfully*

# Unix users can map to different SMB User names
;  username map = /etc/samba/smbusers

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /etc/samba/smb.conf.%m

# Most people will find that this option gives better performance.
# See speed.txt and the manual pages for details
   socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192
   add machine script = /usr/sbin/useradd -d /dev/null -g samba-clients -s /bin/false -M % u   
# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
;   interfaces = 192.168.12.2/24 192.168.13.2/24

# Configure remote browse list synchronisation here
#  request announcement to, or browse list sync from:
#   a specific host or from / to a whole subnet (see below)
;   remote browse sync = 192.168.3.25 192.168.5.255
# Cause this host to announce itself to local subnets here
;   remote announce = 192.168.1.255 192.168.2.44

# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
   local master = Yes

# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
   os level = 99

# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
   domain master = yes

# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
   preferred master = yes

# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
   domain logons = yes

# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
#   logon script = %m.bat   
# run a specific logon batch file per username
   logon script = custom.bat

# Where to store roving profiles (only for Win95 and WinNT)
#        %L substitutes for this servers netbios name, %U is username
#        You must uncomment the [Profiles] share below
   logon path = \\172.17.1.116\Profiles\ % U

# All NetBIOS names must be resolved to IP Addresses
# 'Name Resolve Order' allows the named resolution mechanism to be specified
# the default order is "host lmhosts wins bcast". "host" means use the unix
# system gethostbyname() function call that will use either /etc/hosts OR
# DNS or NIS depending on the settings of /etc/host.config, /etc/nsswitch.conf
# and the /etc/resolv.conf file. "host" therefore is system configuration
# dependant. This parameter is most often of use to prevent DNS lookups
# in order to resolve NetBIOS names to IP Addresses. Use with care!
# The example below excludes use of name resolution for machines that are NOT
# on the local network segment
# - OR - are not deliberately to be known via lmhosts or via WINS.
; name resolve order = wins lmhosts bcast

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
;   wins support = yes

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
#   Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one   WINS Server on the network. The default is NO.
;   wins proxy = yes

# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The built-in default for versions 1.9.17 is yes,
# this has been changed in version 1.9.18 to no.
   dns proxy = no

# Case Preservation can be handy - system default is _no_
# NOTE: These can be set on a per share basis
;  preserve case = no
;  short preserve case = no
# Default case is normally upper case for all DOS files
;  default case = lower
# Be very careful with case sensitivity - it can break things!
;  case sensitive = no

#============================ Share Definitions ==============================
   idmap uid = 16777216-33554431
   idmap gid = 16777216-33554431
   template shell = /bin/false
   winbind use default domain = no
[homes]
   comment = Home Directories
   browseable = no
   writable = yes

# Un-comment the following and create the netlogon directory for Domain Logons
 [netlogon]
   comment = Network Logon Service
   path = /home/netlogon
;   guest ok = Yes
   writable = No
   share modes = No


# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
[Profiles]
    comment = User Profiles   
    path = /profiles
    readonly = No
    inherit permissions = Yes
    browseable = No
    create mask = 0600
    directory mask = 0700
;    guest ok = Yes


# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
   comment = All Printers
   path = /var/spool/samba
   browseable = no
# Set public = yes to allow user 'guest account' to print
   guest ok = no
   writable = no
   printable = yes

# This one is useful for people to share files
;[tmp]
;   comment = Temporary file space
;   path = /tmp
;   read only = no
;   public = yes

# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
;   comment = Public Stuff
;   path = /home/samba
;   public = yes
;   read only = yes
;   write list = @staff

# Other examples.
#
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
;   comment = Fred's Printer
;   valid users = fred
;   path = /homes/fred
;   printer = freds_printer
;   public = no
;   writable = no
;   printable = yes

# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
;   comment = Fred's Service
;   path = /usr/somewhere/private
;   valid users = fred
;   public = no
;   writable = yes
;   printable = no

# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %u option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
;  comment = PC Directories
;  path = /usr/pc/%m
;  public = no
;  writable = yes

# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
;   path = /usr/somewhere/else/public
;   public = yes
;   only guest = yes
;   writable = yes
;   printable = no

# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
;   comment = Mary's and Fred's stuff
;   path = /usr/somewhere/shared
;   valid users = mary fred
;   public = no
;   writable = yes
;   printable = no
;   create mask = 0765

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #5 Online: 08 de Agosto de 2010, 18:24 »
Vc não criou compartilhamento pra essas pastas??? Está compartilhando como, por "usershare"???

executa um comando pra mim aí:

smbclient -L //<nome-do-seu-servidor> -U <nome-de-usuario-valido>

P.ex. "smbclient -L //servidor -U queiroz"

Cola o resultado aqui.
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #6 Online: 08 de Agosto de 2010, 20:22 »
mudei meu smb.conf, agora não acesso nada. Consigo ver o servidor, vejo uma pasta que criei e não consigo acessa-la.
.
.
[global]
workgroup = GRUPO
netbios name = KALIB
server string = Servidor de Arquivos
log level = 3
log file = /var/log/samba/log.%m
domain logons = Yes
os level = 65
preferred master = Yes
domain master = Yes
dns proxy = No
wins support = Yes
ldap ssl = no
comment = Servidor de Arquivos
security = share

[Downloads]
comment = downloads em servidor
path = /home/servidor/Downloads
available = yes
browseable = yes
writable = yes
guest ok = yes
public = yes
printable = no
locking = no
create mode = 777
directory mask = 777
force user = nobody
force group = nobody

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #7 Online: 08 de Agosto de 2010, 21:07 »
Mas pq vc mudou a máquina de workgroup????  ???
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #8 Online: 09 de Agosto de 2010, 12:47 »
boa tarde.
Agora estou conseguindo acessar o outro hd, só que para acessa-lo em rede tenho que ir no ubuntu clicar em locais e depois no hd slave. Se não fizer isso, nao entra. Tem que fazer a montagem dele primeiro para depois acessa-lo. Entao, pergunta: Como fazer para que o linux possa monta-lo na hora do boot, automaticamente?

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #9 Online: 09 de Agosto de 2010, 12:52 »
Adicione uma entrada para cada partição dele no arquivo /etc/fstab.

Mas isso não deveria ter a ver com o Samba...
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline sot-legend

  • Usuário Ubuntu
  • *
  • Mensagens: 237
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #10 Online: 09 de Agosto de 2010, 14:04 »
altere a permissão na pasta que você não consegue acessar, caso sua pasta esteja dentro de /home/USUARO/ faça assim:

Código: [Selecionar]
# chmod -R 777 /home/USUARIO/Compartilhamento

Neste exemplo coloquei o nome da pasta como compartilhamento, faça isso e poste o resultado.
][_, {[]} ][_,

»|.¶åŭĽĭŋĥØ.|«

Offline zekkerj

  • Usuário Ubuntu
  • *
  • Mensagens: 19.735
  • Gratidão gera gratidão, lamúria atrai lamúria...
    • Ver perfil
    • Blog do Zekke
Re: [Samba] Compartilhando dois hds.
« Resposta #11 Online: 09 de Agosto de 2010, 14:20 »
Isso não vai funcionar.
Pesquise antes de perguntar, sua dúvida pode já ter sido respondida.
Não respondo dúvidas por MP, coloque sua dúvida no fórum onde ela pode ser pesquisada pelos seus colegas!
Não venha ao fórum apenas para perguntar. Se você sabe a resposta de um problema, porque não ajudar seu colega? ;D

Offline marcionugas

  • Usuário Ubuntu
  • *
  • Mensagens: 100
    • Ver perfil
Re: [Samba] Compartilhando dois hds.
« Resposta #12 Online: 10 de Agosto de 2010, 15:01 »
RESOLVIDO!!

Fui no terminal e digitei:
$sudo apt-get install ntfs-config



Em seguida adcionei a partição ou hd pelo ambiente gráfico (Sistema >

Administração > Ferramenta de configuração NTFS.

Obrigado a todos.